Click to Home
Site Tools
Mountains
Valdez Alaska

Go To Search
Boat Yard
Overview
Valdez Small Boat Harbor is the ideal location for performing your annual and unexpected vessel maintenance in an environmentally friendly facility.

Vessel Maintenance Facilities
  • 75 ton marine travelift
  • Boat launch ramp usable at all tides
  • Eight 24 ft. by 60 ft. concrete vessel maintenance stations equipped with water, 110 and 220 volt electrical service
  • Fishermen’s dock equipped with #8,500 and #14,000 marine hoists
  • Restrooms, showers and vessel pump-out facilities located within the harbor
  • Tidal grid capable of handling vessels up 120 feet in length and not more than 250 gross tons
  • Two 40 feet by 80 feet concrete wash-down pads equipped with water, 110 and 220 volt electrical service

Services Available to Vessels
The following services are available to vessels at the boat yard:
  • Air freight
  • Commercial divers
  • Commercial motor carriers
  • Freezer Storage
  • Marine supply stores
  • Two marine fuel docks
  • UPS, FEDEX, and USPS
  • Welding and fabrication shops

Best Management Practices
  • Anti-fouling paints containing the minimum amount of toxin necessary for the expected conditions is strongly recommended. Avoid the use of soft ablative paints and use water based paints where possible.
  • Any maintenance involving blasting, chipping, sanding, or other ablative / abrasive removal of material or paint shall be done over canvas or plastic tarps. If water blasting is conducted, filter fabric may be used instead of canvas or plastic tarps to allow water to pass through. These activities shall be done in an enclosed or sheltered structure or in a tarped enclosure to contain airborne debris and dust.
  • Clean engine repair areas regularly using dry cleanup methods. Capture petroleum spills with absorbent pads and materials. Do not hose down the repair area with water.
  • Collected paint chips, dust, sediment, blast grit, and similar debris shall be placed in containers approved for such material and disposed of according to federal, state, and local regulations. This material shall not be disposed of in the trash or construction materials dumpsters.
  • Minimize the use of spray painting equipment. Use brushes and rollers whenever possible. Spray painting is prohibited over water. Designate an area to mix paints, solvents, and reducers. Keep records of paint use, type, application, amount required, etc. All spray painting shall be conducted over land in a spray booth or under a tarp.
  • Store engine parts and engines on impervious surfaces. Do not wash engine parts over bare ground or water. Adopt alternatives to solvent-based parts washers such as Bioremediating systems that take advantage of microbes to digest petroleum. If using solvent to clean engine parts, do so in a container parts washer with a lid to prevent evaporation of volatile organic compounds. Use drip pans when handling any type of liquid and use separate drip pans for each fluid to avoid mixing. Use funnels to transfer fluids and drain all parts of fluid prior to disposal.
  • Store opened containers of useable solvents and paints in covered, UL-listed, or Factory Mutual approved containers. Use only one cleaning solvent to simplify disposal and use only the minimal amount of solvent needed for a given job. Use soy-based solvents and other similar products with no or low volatility.
  • There may be additional requirements mandated by Alaska Department of Environmental Conservation, various federal and state regulations, and/or other regulatory agencies. You are required to know and comply with these regulations
  • Winterizing: Use propylene glycol antifreeze for all systems; it is less toxic than ethylene glycol. Ethylene glycol should never be used in potable water systems; it is highly toxic and cannot be purged reliably. Add stabilizers to fuel to prevent degradation. Be sure fuel tanks are 85% - 90% full to prevent flammable fumes from accumulating and to minimize the possibility of condensation leading to corrosion. Do not fill the tank more than 90% full. Use the highest rated octane recommended by the engine manufacturer; premium fuels are more stable than others are. Be sure the gas cap seals tightly.
  • Work areas shall be cleaned after each operation is completed or at the end of the day. Remove all trash, debris, paint chips, fiberglass, blast grit, and residue etc. All maintenance shall be conducted in designated areas.

Resources